Product Overview
Item Type: Remote Battery Disconnect Switch
Operating Voltage: Dc9v-28v
Operating Frequency: 433.92mhz or 315mhz
Static Current: 5ma
Load Power: 800w
Pairing Method: Keystroke Learning
Reception Sensitivity: >97dbm
Working Mode: Point Self - Locking Interlocking Timing
Support Encoding Chip: Learning Code 1527
Operating Temperature: -10 degrees Celsius +70 degrees Celsius
Battery Model: 1 x Cr2016 Capacity 75mah (One Battery per Remote) (Shipped with Built-In Battery)
Description of setting four working modes of wireless remote control switch:
The Wireless Control Switch has Four Working Modes: Instant mode (click), switching mode (self‑locking), locking mode (interlocking)
Instant Mode (Click) : After the mode is paired successfully, press and hold the remote control button (e.g. A), and the corresponding relay on the receiver will open; Release the remote control button (e.g. A) and the corresponding relay on the receiver closes;
Switching Mode (Self‑locking) : After the mode is paired successfully, press the remote control button (e.g. A), and the corresponding relay on the receiver will open; Press the remote control button again (e.g. A), and the corresponding relay on the receiver closes;
Lock Mode (Interlock) : After the mode is paired successfully, press the remote control button (e.g. A) and the receiver relay will open; Press the remote control button (e.g. B) and the relay on the receiver turns off.
Delay Mode (delay 5 seconds, 10 seconds, 15 seconds, 20 seconds off):
After the mode is paired successfully, press the button of the remote control (e.g. A), and the corresponding relay on the receiver will open; Disconnect after delay to the corresponding time. (Press the receiver button 4 times for pairing, delay 5S to close the corresponding relay; Press the receiver button five times for pairing, and delay for 10S to turn off the corresponding relay; Press the receiver button 6 times for pairing, delay 15S to close the corresponding relay; Press the receiver button 7 times for pairing, delay 20S to close the corresponding relay; Press the remote control again when the relay is not closed, then delay timing will start again)
Set the Working Mode of the Wireless Remote Control Switch
Observe the indicator status carefully. If the indicator is incorrectly set, the receiver will not work properly.
Set Instant Mode (Click):
Press the Learn button on the receiver once. Wait for the LBD on the receiver to light up and enter the setting state,
Step 2) Press the button on the force controller (e.g. Button A) once. The LED indicator on the receiver will blink and then go off. The click mode is set successfully.
Set Switching Mode (Self‑locking) :
Step 1) Press the Learn button on the receiver twice. Wait for the LED on the receiver to light up and enter the setting state.
Step 2) Press the button on the controller (e.g. Button A) once. The LED indicator on the receiver will blink and then go off. The self‑locking mode is set successfully
Set Locking Mode (Interlock) :
Step 1) Press the Learn button on the receiver 3 times. Wait for the LED on the receiver to light up and enter the setting state.
Step 2) Press the button on the remote control (such as button A) once. The LED indicator on the receiver will be shuo, then steady on; At this point, press another button on the remote control (such as button B) once, and the LED indicator on the receiver will blink and then go off. The interlock mode is set successfully.
Delay Mode (Timing) :
Step 1) Press the learning button on the receiver as required (the delay shutdown time is: press the learning button on the receiver 4 times, then the delay is 5 seconds to close, 5 times 10 seconds, 6 times 15 seconds, 7 times 20 seconds) wait for the LED on the receiver to light up and enter the setting state.
Step 2) Press the button on the controller (such as button A) once. The LED indicator on the receiver will blink and then go off. The delay mode is set successfully.
Operating Voltage: Dc9v-28v
Operating Frequency: 433.92mhz or 315mhz
Static Current: 5ma
Load Power: 800w
Pairing Method: Keystroke Learning
Reception Sensitivity: >97dbm
Working Mode: Point Self - Locking Interlocking Timing
Support Encoding Chip: Learning Code 1527
Operating Temperature: -10 degrees Celsius +70 degrees Celsius
Battery Model: 1 x Cr2016 Capacity 75mah (One Battery per Remote) (Shipped with Built-In Battery)
Description of setting four working modes of wireless remote control switch:
The Wireless Control Switch has Four Working Modes: Instant mode (click), switching mode (self‑locking), locking mode (interlocking)
Instant Mode (Click) : After the mode is paired successfully, press and hold the remote control button (e.g. A), and the corresponding relay on the receiver will open; Release the remote control button (e.g. A) and the corresponding relay on the receiver closes;
Switching Mode (Self‑locking) : After the mode is paired successfully, press the remote control button (e.g. A), and the corresponding relay on the receiver will open; Press the remote control button again (e.g. A), and the corresponding relay on the receiver closes;
Lock Mode (Interlock) : After the mode is paired successfully, press the remote control button (e.g. A) and the receiver relay will open; Press the remote control button (e.g. B) and the relay on the receiver turns off.
Delay Mode (delay 5 seconds, 10 seconds, 15 seconds, 20 seconds off):
After the mode is paired successfully, press the button of the remote control (e.g. A), and the corresponding relay on the receiver will open; Disconnect after delay to the corresponding time. (Press the receiver button 4 times for pairing, delay 5S to close the corresponding relay; Press the receiver button five times for pairing, and delay for 10S to turn off the corresponding relay; Press the receiver button 6 times for pairing, delay 15S to close the corresponding relay; Press the receiver button 7 times for pairing, delay 20S to close the corresponding relay; Press the remote control again when the relay is not closed, then delay timing will start again)
Set the Working Mode of the Wireless Remote Control Switch
Observe the indicator status carefully. If the indicator is incorrectly set, the receiver will not work properly.
Set Instant Mode (Click):
Press the Learn button on the receiver once. Wait for the LBD on the receiver to light up and enter the setting state,
Step 2) Press the button on the force controller (e.g. Button A) once. The LED indicator on the receiver will blink and then go off. The click mode is set successfully.
Set Switching Mode (Self‑locking) :
Step 1) Press the Learn button on the receiver twice. Wait for the LED on the receiver to light up and enter the setting state.
Step 2) Press the button on the controller (e.g. Button A) once. The LED indicator on the receiver will blink and then go off. The self‑locking mode is set successfully
Set Locking Mode (Interlock) :
Step 1) Press the Learn button on the receiver 3 times. Wait for the LED on the receiver to light up and enter the setting state.
Step 2) Press the button on the remote control (such as button A) once. The LED indicator on the receiver will be shuo, then steady on; At this point, press another button on the remote control (such as button B) once, and the LED indicator on the receiver will blink and then go off. The interlock mode is set successfully.
Delay Mode (Timing) :
Step 1) Press the learning button on the receiver as required (the delay shutdown time is: press the learning button on the receiver 4 times, then the delay is 5 seconds to close, 5 times 10 seconds, 6 times 15 seconds, 7 times 20 seconds) wait for the LED on the receiver to light up and enter the setting state.
Step 2) Press the button on the controller (such as button A) once. The LED indicator on the receiver will blink and then go off. The delay mode is set successfully.
Features
1、Anti Theft Design: This car battery disconnect switch system, when you do not need to use the car, through the remote control to cut off the battery power, prevent your car from being stolen.
2、Convenient: This remote controlled battery switch allows you to move the trigger from under the hood to your hand, quickly cutting off the power supply just by remote control, safe and convenient.
3、Durable Material: Our remote disconnect switch is made of heat resistant ABS plastic with metal contacts for better electrical conductivity.
4、Four Working Modes: This wireless control switch has four working modes: instant mode (click), switching mode (self locking), locking mode (interlocking), delay mode (timing), which can be used only after setting.
5、Wide Applications: Our remote battery disconnect switch system can be widely used in cars and any other engine application with 12 volt batteries.
Package List
1 x Switch
1 x Remote Control
1 x Battery Clip
1 x Brass Nose
1 x Screw
1 x Nut
1 x Rubber Hose
Package Weight and Dimension
| Weight | 0.66 lb |
| Width | 4.68 Inch |
| Height | 2.34 Inch |
| Length | 6.24 Inch |
